input output settings and dhcp

[luke]

Hi i have everything setting up on a pi 4, but having troubles setting up the input and the output network ips, how should i do the dhcp ips

[luke]

Hi i have everything setting up on a pi 4, but having troubles setting up the input and the output network ips, how should i do the dhcp ips

[shak4031]

I had the same confusion, but the below worked for me.  This is for using Keexybox as primary entry point for all devices (DNS/DHCP/Gateway).

1) set Input network to different subnet then your primary router.
      ex. Router IP is 192.168.1.1
             interface eth0 (for both input and output)
             input to 192.168.2.254
             output to 192.168.1.254

[shak4031]

I had the same confusion, but the below worked for me.  This is for using Keexybox as primary entry point for all devices (DNS/DHCP/Gateway).

1) set Input network to different subnet then your primary router.
      ex. Router IP is 192.168.1.1
             interface eth0 (for both input and output)
             input to 192.168.2.254
             output to 192.168.1.254

[benoit]

Hi,

Let's say that your router has the IP 192.168.1.1/24 and it is a DNS server. Here is an example of configuration for your KeexyBox:

Input network (network that will reach your devices)
- Interface: eth0
- IP address: 192.168.2.254
- Netmask: 255.255.255.0

Output network (network that will reach your router)
- Interface: eth0
- IP address: 192.168.1.254
- Netmask: 255.255.255.0

DNS and Gateway
- Gateway: 192.168.1.1
- DNS 1: 192.168.1.1
- DNS 2: (Leave blank)

It is also recommended to disable DHCP on the router and enable it on Keexybox. Here is an example of DHCP configuration for your KeexyBox:

Address range for the network: 192.168.2.0/24
 - Enable DHCP (checked)
 - DHCP start IP: 192.168.2.151
 - DHCP end IP: 192.168.2.201

Address range for the network: 192.168.1.0/24
 - Enable DHCP (checked)
 - DHCP start IP: 192.168.1.151
 - DHCP end IP: 192.168.1.201

Reboot Keexybox when you are done.

I hope this will help.

[benoit]

Hi,

Let's say that your router has the IP 192.168.1.1/24 and it is a DNS server. Here is an example of configuration for your KeexyBox:

Input network (network that will reach your devices)
- Interface: eth0
- IP address: 192.168.2.254
- Netmask: 255.255.255.0

Output network (network that will reach your router)
- Interface: eth0
- IP address: 192.168.1.254
- Netmask: 255.255.255.0

DNS and Gateway
- Gateway: 192.168.1.1
- DNS 1: 192.168.1.1
- DNS 2: (Leave blank)

It is also recommended to disable DHCP on the router and enable it on Keexybox. Here is an example of DHCP configuration for your KeexyBox:

Address range for the network: 192.168.2.0/24
 - Enable DHCP (checked)
 - DHCP start IP: 192.168.2.151
 - DHCP end IP: 192.168.2.201

Address range for the network: 192.168.1.0/24
 - Enable DHCP (checked)
 - DHCP start IP: 192.168.1.151
 - DHCP end IP: 192.168.1.201

Reboot Keexybox when you are done.

I hope this will help.